Last updated: September 1, 2025
Short answer
✅ Stability: Single-leg base (solid root stump) = very stable. Hand test: lightly push → no rocking.
✅ Glass support: in a milled recess, all-round play 0.1–0.5 cm, ESG/VSG 8–12 mm, anti-slip buffers.
✅ Use: Felt gliders for floor protection; direct sunlight and underfloor heating are not critical in everyday living spaces.
Classification
Teak root tables are unique pieces made of hard, oil-rich hardwood (Janka hardness approx. 1450 lbf ). Our standard design uses a single, solid root stump as the base —a "monopod" with a very wide support. This results in a very low center of gravity and a large base : extremely stable for everyday use.
Note: The teak used is already properly prepared before production ; here we therefore focus on construction, use and maintenance .
Correctly assess stability (purchase & everyday use)
-
Single-leg base (mono-base): The broad support of the root stump supports the weight centrally. Typically, no three-point support is necessary —the shape inherently ensures stability and stability .
-
Check proportions:
-
Base diameter vs. glass/table top size : the larger the table top, the wider the base should be.
-
Center of gravity : Glass/central zone is centered over the strongest part of the base, not “hanging” on a cantilever.
-
-
Hand test in the showroom: Gently push the table with your hand in all directions . A good piece won't swing and won't show any tendency to tip over .
-
Fine-tuning at home: If the floor is slightly uneven, felt pads/pads (see below) will help ensure the perfect support.
Glass shelf: proven solution, easy to clean
-
Support type: A milled recess ("pocket") in the wood is common. The glass pane rests in this groove under its own weight — it's not glued , removable at any time, and easy to clean.
-
Play/Gap: A gap of approximately 0.1–0.5 cm between the glass and the groove is ideal. This allows the pane room for thermal expansion and facilitates insertion and removal.
-
Glass selection: tempered/laminated safety glass, often 8–12 mm . Transparent, anti-slip buffers at the contact points protect the glass and wood.
Floor protection (teak is hard – the floor stays beautiful)
-
Why is it useful? Teak is very hard ; point loads can mark sensitive floors.
-
Recommendation: Glue generous felt pads under the contact surface (to adjust the height if necessary), and keep it dust-free regularly (sand acts like emery).
Sun & underfloor heating
-
Direct sunlight: This is not critical for teak root tables in everyday living spaces . The oil-rich wood is naturally very durable ; the glass top is also suitable for warm light.
-
Underfloor heating: Unproblematic. Teak exhibits very good climate resistance ; standard underfloor heating in living rooms will not cause any damage.
-
Installation tips: Only keep a certain distance from point heat sources (e.g. directly in front of a stove) to prevent glass/metal parts from overheating.
Care – short & clear
-
Cleaning: Remove dust dry; remove stains with a slightly damp cloth.
-
Oil refresher (optional, 1–2 times per year): Apply a thin layer, allow to absorb for 20–30 minutes , then polish dry .
-
In everyday life: Use coasters for very hot/humid vessels; wipe off water promptly.
Purchase checklist
-
Base width vs. slab size plausible? Is the center of gravity in the middle?
-
Hand test passed: no tipping moment, no oscillation.
-
Glass support: clean recess, 0.1–0.5 cm circumferential joint, buffer present.
-
Floor contact: felt gliders included.
-
Installation location: Sunny/with underfloor heating? → Both are okay .
Showroom & Visit (Zurich Region)
Best time: 11:30–17:00 – please confirm appointment in advance.
Information on directions, entrance, parking & bell: Contact
Summary (quick overview):
Teak root tables are stable for everyday use because a solid root stump acts as a single-leg base, creating a low center of gravity and a large support surface. When purchasing, check the proportions: base width to table top size, center of gravity in the middle; do the hand test in the showroom (gently tap it – the table should not tip or resonate). The glass tabletop rests loosely in a milled recess; ideally, 0.1–0.5 cm of play all around is required, with anti-slip buffers, typically 8–12 mm toughened/laminated glass. Use large felt glides on the floor and keep contact points clean. Direct sunlight and standard underfloor heating are generally not a problem with teak. Care instructions in brief: Apply a thin coat of oil 1–2 times a year, let it soak in for 20–30 minutes, polish dry, and wipe off any moisture promptly. Conclusion: Construction and correct installation determine noticeable stability.